Image
Part Number -
T-WNB-3Y-208
WattNode 208/240 VAC 1,2, or 3 Phase Wye kWh Transducer Sensor
$340.00 USD
For sub-metering, net-metering, energy management, and performance contracting applications, the WattNode 208/240 VAC 1,2, or 3 Phase Wye kWh Transducer Sensor works with Magnelab AC Current Transformers and a Pulse Input Adapter to provide True RMS kilowatt hours of energy used, even for loads with non-sinusoidal waveforms.
Overview
Provides accurate measurement at a low cost to meet your needs for sub-metering, net-metering, energy management, and performance contracting applications. This WattNode Wye-connection kWh Transducer works with Magnelab AC Current Transformers and a Pulse Input Adapter to provide True RMS kilowatt hours of energy used, even for loads with non-sinusoidal waveforms. Because these sensors tie directly into the line, they should only be used by qualified personnel. This model supports a 1,2, or 3-phase wye-connection of 208/240 VAC.
Features
- Measures 1, 2, or 3 phases in 2, 3, or 4 wire configurations
- Use with wide choice of CTs (sold separately); ratings from 5 to 1500 amps
- Accurate measurement of 1-,2-, or 3-phase configurations
- Easy to install and wire
- Pulse output: compatible with pulse input logger models
- Small size: can be installed in existing service panels or junction boxes
- Diagnostic LEDs: confirms proper installation for all phases
- Bidirectional metering: net metering for PV (photovoltaic) solar and wind power generation with only one meter
- Metering of variable frequency drives
- Line powered: no external supply required
- Detachable terminal blocks: easy to install and remove
- UL, cUL listed: designed and tested for safety and use throughout North America
- CE Mark: can be installed throughout the EU
Specifications
Operating: voltage range: ±20% of nominal
Frequency: 60 Hz
CT input: 0-0.5 VAC operating, 3 VAC maximum
Connectors: UL, CSA recognized, detachable screw terminals (14 AWG), 600V
Operating temp range: -30 to 60°C (-22 to 140°F)
Operating humidity range: 0 to 90% RH, non-condensing
Dimensions: 8.5 cm x 14.3 cm x 3.8 cm (3.3 in. x 5.6 in. x 1.5 in.)
Weight: 295 g (10.4 oz.)
Number of data channels: 2
To download the manual from Continental Control Systems LLC click here.
Here is an image of a typical installation:
Image
- Wye configuration ranges: 120, 208, 240 Volts AC
- 1 Phase 2 Wire 120V (with neutral)
- 1 Phase 3 Wire 120V/240V
- 3 Phase 4 Wire 120V/208V
- Accuracy: ±0.45% of reading + 0.05% FS through 25th harmonic
- (dependent on CT used and line variation accuracy could be 1.5% to 4% of reading)
Compatible items
AC Current
Pulse Input
Voltage Input Lead Set
Sensors
USB Data Loggers - requires external sensor(s)
USB Data Loggers - w/external sensor(s)
Web-based Monitoring Systems - via remote communication
Recently Viewed
Sensor
20 AMP Mini Split-core AC Current Transformer Sensor
A small 20 AMP split-core AC Current Transformer (CT) mounted around a current carrying wire to measure AC amperage; used with HOBO data loggers via the FlexSmart TRMS module and with kWh transducers (WattNodes) for True RMS measurement of sinusoidal and non-sinusoidal waveforms.
Sensor
Compressed Air Flow Meter Sensor
Effectively monitors compressed air systems; includes two probes, one warmer than the other, to calculate mass velocity based on heat requirements.
Sensor
5 AMP Mini Split-core AC Current Transformer Sensor
A small 5 AMP split-core AC Current Transformer (CT) mounted around a current carrying wire to measure AC amperage; used with HOBO data loggers via the FlexSmart TRMS module and with kWh transducers (WattNodes) for True RMS measurement of sinusoidal and non-sinusoidal waveforms.
Sensor
10 AMP Mini Split-core AC Current Transformer Sensor
The small size 10 AMP split-core AC Current Transformer (CT) is mounted around a current carrying wire to measure AC amperage. This CT provides a .333 Volt AC output proportional to current flow and is used with Onset data loggers via the FlexSmart TRMS module and with kWh transducers (WattNodes) for True RMS measurement of sinusoidal and non-sinusoidal waveforms.