Part Number - UX90-001
HOBO State Data Logger
$130.00 USD
Records state changes, electronic pulses, and mechanical or electrical contact closures from external sensing devices.
Important Information
Requires HOBOware software and a USB cable. (Note: A USB-A to USB-B mini cable is included w/HOBOware Pro USB Drive software purchase). See compatible items below.
Compatible with
Overview
Records state changes, electronic pulses, and mechanical or electrical contact closures from external sensing devices. Ideal for monitoring energy consumption, mechanical equipment operation, and water and gas flow.
Item number UX90-001M has been discontinued.
Features
- One logger with four recording modes
- Internal reed switch can be used to determine when a door or window is open or closed
- Compatible with a wide range of external sensors
- Ships with 2.5 mm input cable
- Compatible with HOBOware and HOBOware Pro software for logger setup and graphing & analysis
Specifications
Internal Sensor
- Maximum State, Event, Runtime Frequency
-
1 Hz
- Preferred Switch State
-
No magnet present (normally open)
External Input
- External Contact Input
-
Electronic solid state switch closure or logic driven voltage output
- Range
-
0 to 3 V DC (USB powered), 0 to 2.5 V DC (battery powered)
- Maximum Pulse Frequency
-
50 Hz
- Maximum State, Event, Runtime Frequency
-
1 Hz
- Pulse, Event Lockout Time
-
0 to 1 second in 100 ms steps
- Solid State Switch Closure
-
Input Low: < 10 KΩ; Input High: > 500 KΩ
- Internal Weak Pull-Up
-
100 KΩ
- Input Impedance
-
Solid state switch closure: 100 KΩ pull up
Logger
- Resolution
-
Pulse: 1 pulse, Runtime: 1 second, State and Event: 1 State or Event
- Logging Rate
-
1 second to 18 hours, 12 minutes, 15 seconds
- Memory Modes
-
Wrap when full or stop when full
- Start Modes
-
Immediate, push button, date & time, or next interval
- Stop Modes
-
When memory full, push button, or date & time
- Time Accuracy
-
±1 minute per month at 25°C (77°F) (see Plot A)
- Power Source
-
One 3V CR2032 lithium battery and USB cable
- Battery Life
-
1 year, typical with logging intervals greater than 1 minute and normally open contacts
- Memory
-
UX90-001: 128 KB (84,650 measurements, maximum)UX90-001M: 512 KB (346,795 measurements, maximum)
- Download Type
-
USB 2.0 interface
- Full Memory Download Time
-
10 seconds for 128 KB; 30 seconds for 512 KB
- Logger Operating Range
-
Logging: -20° to 70°C (-4° to 158°F); 0 to 95% RH (non-condensing)Launch/Readout: 0° to 50°C (32° to 122°F) per USB specification
- LCD
-
LCD is visible from: 0° to 50°C (32° to 122°F); the LCD may react slowly or go blank in temperatures outside this range
- Size
-
3.66 x 5.94 x 1.52 cm1.44 x 2.34 x 0.6 in.
- Weight
-
23 g0.81 oz
- Environmental Rating
-
IP50
Image
Compatible items
Compliance Certificates
Communication Cables
Batteries
Graphing & Analysis
What's in the box
- HOBO UX90-001x State Data Logger
- 2.5 mm input cable
- Command™ strip
- Double-sided tape
- Hook & loop strap
- Magnet with 2 screws
Customers Also Bought
Sensor
AC Current Switch Sensor
Measures equipment runtime (time-of-use); compatible with HOBO UX90 and UX120-017 data loggers.
Sensor
WattNode 208/240 VAC 3-phase Delta/Wye kWh Transducer Sensor
For sub-metering, net-metering, energy management, and performance contracting applications, the WattNode 208/240 VAC 3-phase Delta/Wye kWh Transducer Sensor works with Magnelab AC Current Transformers and a Pulse Input Adapter to provide True RMS kilowatt hours of energy used, even for loads with non-sinusoidal waveforms.
Sensor
WattNode 480 VAC 3-phase Delta/Wye kWh Transducer Sensor
For sub-metering, net-metering, energy management, and performance contracting applications, the WattNode 480 VAC 3-phase Delta/Wye kWh Transducer Sensor works with Magnelab AC Current Transformers and a Pulse Input Adapter to provide True RMS kilowatt hours of energy used, even for loads with non-sinusoidal waveforms.