Image
Part Numbers
T-CON-ACT-150
•T-CON-ACT-300
ConLab Volt AC Transmitter Sensor
$200.00 USD
A self-powered transformer for monitoring sine wave and single-phase AC voltage; compatible with HOBO MX1100, UX120-006M, ZW series, and U series data loggers.
Important Information
Refer to data logger product pages to ensure you have the proper interfaces (modules, adapter, etc.) to deploy this sensor.
Overview
The AC Voltage transmitter is a self-powered transformer for monitoring sine wave and single-phase AC voltage. Available in two ranges: 0 to 150 Volts AC, and 0 to 300 Volts AC.
Requirements for use with specific data loggers:
- HOBO MX1100 series: a 4-20mA input cable (SD-MA-420)
- HOBO U12, UX120-006M, or ZW series: a 4-20mA input cable (CABLE-4-20mA)
Features
- Available in 2 ranges: 0 to 150 & 0 to 300 Volts AC
- Requires an input cable (part # CABLE-4-20mA)
Specifications
- Ranges: 0-150 and 0-300 volts RMS
- Sensor accuracy: < ±0.1% of span (20% to 120% of range) ±0.25% of span (10% of range)
- Over range: +20% of span
- Over load: +40% of span
- Frequency: 60 Hz AC
- Supply: Self-powered
- Output: 0–20 mA
- Response time to 90%: <240 msec
- Operating conditions: -20° to 70°C (-4° to 158°F); 5-95% RH, non-condensing
- Housing: Plastic polycarbonate
- Protection Level
Box: According to IP-50 DIN 40050
Terminals: According to IP-10 DIN 40050 - Mounting: Standard 35mm DIN rail
Notes: Because these sensors tie directly into the line, they should be used only by qualified personnel.
Requirements
- For U12 & H8 Loggers: Input Cable (Part # CABLE-4-20mA)
- For HOBO Energy Logger: FlexSmart Analog Module (Part # S-FS-CVIA)
Compatible items
Bluetooth (BLE) Data Loggers
USB Data Loggers - requires external sensor(s)
4-20 mA
Recently Viewed
Sensor
75 AMP Mini Split-core AC Current Transformer Sensor
A small 75 AMP split-core AC Current Transformer (CT) mounted around a current carrying wire to measure AC amperage; used with HOBO data loggers via the FlexSmart TRMS module and with kWh transducers (WattNodes) for True RMS measurement of sinusoidal and non-sinusoidal waveforms.
Sensor
WattNode 480 VAC 3-phase Wye kWh Transducer Sensor
Effective immediately Onset no longer supplies the T-WNB-3Y-480 WattNode 480 VAC 3-phase Wye kWh Transducer. The recommended upgrade is our T-WNB-3D-480 WattNode 480 VAC 3-phase Delta kWh Transducer. Click here to view the T-WNB-3D-480 WattNode 480 VAC 3-phase Delta kWh Transducer.
Sensor
Veris Kilowatt Hour Transducer 1-Phase, 300 Amp Sensor
The Veris AC Kilowatt Transducer incorporates one split-core AC current sensor and two voltage leads and outputs a signal proportional to kilowatts of power (consumption). Accepting an input primary voltage of 208 to 480 Volts AC rms, this transducer requires a Pulse Input Adapter. Because these sensors tie directly into the line, they should be used only by qualified personnel. NOTE: Not recommended for use with variable frequency drives.
Sensor
WattNode 208/240 VAC 1,2, or 3 Phase Wye kWh Transducer Sensor
For sub-metering, net-metering, energy management, and performance contracting applications, the WattNode 208/240 VAC 1,2, or 3 Phase Wye kWh Transducer Sensor works with Magnelab AC Current Transformers and a Pulse Input Adapter to provide True RMS kilowatt hours of energy used, even for loads with non-sinusoidal waveforms.