All Products

All Products

    T-CDI-5x00-x0S

    Effectively monitor compressed air systems with the CDI meter. This flow meter includes two probes, one warmer than the other. This arrangement calculates mass velocity based on heat requirements. Additionally, pipe area data is used to determine flow amounts. 

    Requires analog port selection during U30 system  or RX3000 configuration and use of a S-FS-CVIA when using the H22-001 data logger. When using a UX120-006M, ZW Series or U12 data logger, this sensor requires a 4-20mA input cable (CABLE-4-20mA).

    Add to Cart
    Add to Quote
    Compare Product

    Compare
    T-ASH-G2-x00

    The Ashcroft Gauge Pressure Sensor provides precision pressure measurements in compressed air systems, water, or other compatible gases and fluids with an accuracy of ±1% FS from -20° to 85°C (-4° to 185°F) and only ±1.5% FS -40° to -20°C and 85° to 125°C (-40° to –4°F and 185° to 257°F).

    Requires analog port selection during U30 system or RX3000 configuration and use of a S-FS-CVIA when using the H22-001 data logger. When using a UX120-006M, ZW Series or U12 data logger, this sensor requires an 0-5 Vdc analog input cable (CABLE-ADAP5) and external power provided by an AC adapter (AC-SENS-1).

    Add to Cart
    Add to Quote
    Compare Product

    Compare
    T-CON-ACT-xxx

    The AC Voltage transmitter is a self-powered transformer for monitoring sine wave, single-phase AC voltage. This sensor requires an Input Cable to connect to the UX120-006M, ZW series and U series of data loggers.

    Add to Cart
    Add to Quote
    Compare Product

    Compare
    CABLE-DCVOLT

    The DC Voltage input cable allows you to connect 3rd party sensors with a DC Voltage ouput to the UX120-006M, ZW Series or the U series of data loggers.

    Add to Cart
    Add to Quote
    Compare Product

    Compare
    TMCx-HD

    The TMC temperature probe can be used in air, soil & water work with the UX120-006M, ZW Series or U Series of data loggers. Temperature probes are available in lengths of 0.3 m (1 ft), 1.8 m (6 ft), 6.1 m, (20 ft) & 15.2 m (50 ft).

    Add to Cart
    Add to Quote
    Compare Product

    Compare
    CTV-x

    A split-core AC current sensor records AC amperage for use with U12 Series, UX120-006M and ZW Series of data loggers with external input channels. With an input current of AC current, sine wave, single phase 50 Hz or 60 Hz, load power factor 0.5 to 1.0 lead or lag.

    The molded-plastic housing is rated for indoor use per UL508.

    Add to Cart
    Add to Quote
    Compare Product

    Compare
    T-VER-PX3UL

    The T-VER-PX3UL transducer can measure either air pressure or velocity with the flip of a switch. The PX3 is available in three installation configurations: duct, panel or universal. Duct and panel models have two pressure and velocity range options: 0-1" WC / 0-3,000 ft/min or 0-10" WC / 0-7,000 ft/min with seven field-selectable sub-ranges for pressure and eight for velocity. All variants are available with and without display. The PX3 has an IP65/NEMA 4 environmental rating.

    Requires analog input option during RX3000 or U30 system configuration and use of a S-FS-CVIA when using the H22-001 data logger. When using a U12 data logger, this sensor requires an 0-5 Vdc analog input cable (CABLE-ADAP5) and external power provided by an AC adapter (AC-SENS-1).

    Add to Cart
    Add to Quote
    Compare Product

    Compare
    T-EG-x000-2775

    Rope CTs are excellent for bus-bars and large switch-gear applications. Self-powered rope CTs are flexible and easy to install, but will not be accurate below 30A. Each CT includes the two-pin CT connector plug.

    Technical Specifications

    • 333 mVrms at rated output
    • Accurate within 1% from 30A to stated current rating
    • 6' twisted pair lead with CT connector
    • Note: 30A minimum current required at all times. No external integrator required
    Add to Cart
    Add to Quote
    Compare Product

    Compare
Page 1 / 8